The Tru-Trainer® conveyor belt tracker employs a unique and highly effective tracking action, which is non-damaging to the belt and reacts immediately if the conveyor belt begins to drift off center. Our conveyor belt tracking products deliver superior performance.

TRU-BRITCO FLAT RETURN IDLER

Most Reliable and Re-active Belt Tracking Idlers The Tru-Britco series of conveyor belt tracking idlers are a patented design that offers the most reliable and re-active belt tracking idlers available today
Features and Benefits

Continuous Alignment : by always tracking the belt to the center of the conveyor, it reduces edge damage, spillage and overall better conveyor belt tracking performance.
Heavy-Duty : design of our trainer uses 3 7/16´ bearings, 1 3/4´ shaft, and an abrasive resistant hot-vulcanized rubber cover. Urethane covers are also available.
Patented Design : does not rely on the conveyor belt to activate an arm-type tracking mechanism. By utilizing an internal pivot versus external pivot it does NOT build up with carry back.
Reactionary : in both wet and dry conditions as seen in below ground and above ground mining all over the world.
Total Satisfaction Guarantee (TSG) : to solve your conveyor belt tracking problems and make your overall conveyor system run more efficiently.
Most Reliable and Re-active Belt Tracking Idlers!
The Tru-Trainer® series of conveyor belt tracking idlers are
a patented design that offers the most reliable and re-active
belt tracking idlers available today

TRU-BRITCO DUAL V-RETURN IDLER

Accommodates Excessive Force with V-Return Idler Conveyors
The Tru-Britco Dual V-Return was developed to accommodate the
excessive forces encountered with V-Return idler
conveyors, systems and structures.

Features and Benefits

Two Separate Tapered Rolls : are mounted into the pivot mechanism and can be individually replaced as wear occurs
Designed for High Speed/PIW Conveyors  to opérate and last in severe conditions, wet and dry, and aggressive mining conditions. Conveyor belt speeds that exceed 800 fpm and/or greater than 1500 PIW.
Accommodates Excessive Force : encountered with wide belts and heavy loads.
Enhanced Sealing/Bearing System  needle thrust and tapered roller bearings and enhanced sealing system for the most aggressive mining conditions.
Individual Rollers for Easy Replacement : separate tapered rolls are mounted onto the pivot mechanism, which can be individually replaced as wear occurs.
Available in Urethane (Mine Duty) : Heavy duty rolls 3/4´ polyurethane.

SLIDE-LER

Change Rolls Without Removing Adjacent Idlers BRITCO Slide-ler give you the ability to change rolls under the conveyor loading skirt area without having to remove adjacent belt idlers. This allows the Slide-ler to fit into tight or confined spaces, ensuring proper belt rolling support and ease of change out.

Slide-Ler
BRITCO Slide-ler is a modular designed product that allows you to remove the wing and center roll hangers for easy replacement of your idler rolls. It can also be designed to hold any manufacturer roll in the industry. The Slide-Ler minimizes down time and can be accessed from both sides of the conveyor system. Feature & Benefits
Perfect for Confined Spaces  due to the frames only take-up 8´ (200mm) of width when using 6´ (150mm) rollers.
Improves Safety  and maintenance by allowing rollers to be easily removed without having to remove any of the belt idler frames.
Meets all CEMA Standards  and available in any belt width, troughing angle or idler.
Idler Rolls  we can provide CEMA C, D or E steel or impact rolls.
Slide-Ler (One-Sided)  Also available.

Slide-Ler (Oned-Sided)
BRITCO Slide-Ler (One-Sided) is a patented product designed to be maintained from one side of the conveyor system. This is ideal for systems with access on one side only, where a conveyor is located against the wall or high in the air with catwalk on one side. This allows you to replace rolls with minimal downtime and eliminate the need for man lifts or having to work in a confined space.

Diagram Components

1.    Center Slide
2.    Roller Retainer
3.    Frame
4.    Wing
5.    Steel Roll

ROLLER CASSETTE CONVEYOR BELT IMPACT BED & SLIDER

Incorporate The Advantage Of Sealing
Roller Cassettes incorporate the advantages of slider
and impact bars for sealing, while maintaining
constant rolling support for the conveyor
belt in the load zone.

Features and Benefits

Load Supported : by having up to 4 sets of troughing idlers (12 rolls) in an area that you would normally only have 2 (6 rolls).
* 9 or 12 idler sets are available
* 28´ wide frame, using 6´ (150mm) diameter rolls
* Rolls can be spaced on 5´ (125mm) to 7´ (175mm) centers based on the roll diameter Custom Designed  to suit your particular application.
* Impact, Steel, or Ceramic rollers are available
* Stainless, Galvanized or Steel frames are available Meets All CEMA Standards  and available in any belt width, or troughing angle.
* Eliminate spillage by reducing the conveyor belt deflector between rollers
* Wing rollers can be raised and lowered and center rollers can slide out from either side
* Designed for easy wash out
* Rollers can be spaced on 5´ to 7´ centers based on roll diameter
* Standard steel, impact or ceramic rollers are available
* Wings are fabricated to match any troughing angle